€56.00
(tax excl.)
€67.76
(tax included)
CETOP-5 NG-10 single base bottom outlet. Bottom outlet 1/2" (3/4") Made of Aluminum
OVERCENTER VALVE (BALANCE) SINGLE NG-10
The overcenter valve is used to control movement and block the actuator in both directions, performing the following functions:
- Controlled lowering of the load that is not dragged by its weight, since the valve does not allow any cavitation of the actuator.
- Limitation of the maximum pressure in case of shocks caused by the load, overloads or sudden maneuvers (load control with open center distributor).
- These valves block the oil outlet of the actuator until a pilot pressure is reached in the inlet line that is inversely proportional to the load to be supported by the actuator. In this way, the load does not go into overdrive, and the speed of descent of the load corresponds to the flow controlled by the distributor.
- In case of zero pilot pressure, the pressure necessary to open the valve corresponds to its setting, functioning as a braking valve.
Buy online OVERCENTER VALVE (BALANCE) SINGLE NG-10 at the best price
€405.35
(tax included)
€335.00
(tax excl.)
Reference:
496000
Consult price for large quantities
Related products
€136.99
(tax excl.)
€165.76
(tax included)
CETOP-5 NG-10 center H solenoid valve Maximum pressure 315 bar. Flow rate 160 l/min. Available voltages 12Vdc - 24Vdc - 24Vac - 220V ac - 110Vac SUPPLIED WITH COILS Supplied with connector and 4 screws.
| Reference | PRESSURE | ROADS | Price | Add to cart |
|---|---|---|---|---|
| 496000 | 20 - 200 Bar | TO |
€335.00
|
|
| 496001 | 20 - 200 Bar | b |
€335.00
|
|
| 496002 | 35 - 350 bar | b |
€335.00
|
|
| 496003 | 35 - 350 bar | TO |
€335.00
|
|
12 other products in the same category:
€20.00
(tax excl.)
€24.20
(tax included)
Rexroth Coil R933000030 12 VDC This is an electromechanical component used in hydraulic valves. Its function is to activate or deactivate the flow of oil in a hydraulic circuit upon receiving an electrical signal....
€217.50
(tax excl.)
€263.18
(tax included)
NG-10 pressure reducer
Flow rate 70 l/min.
Pressure range 8....70 and 35.....140 bar.
€168.75
(tax excl.)
€204.19
(tax included)
NG-6 modular pressure reducer Flow rate 35 l/min. Pressure range 8...70 and 35...140 bar.
€108.75
(tax excl.)
€131.59
(tax included)
Modular non-return valve NG-10
Flow rate 70 l/min.
Max pressure 250 bar.
Standard temperature -30 / 80ºC
€75.00
(tax excl.)
€90.75
(tax included)
Modular NG-6 flow regulator.
Flow rate 35 l/min.
Temperature -20 / 70ºC
Maximum pressure 250 bar.
Three regulation options, in line A, in line B and the 2 lines AB
€150.00
(tax excl.)
€181.50
(tax included)
The NG-6 double overcenter valve is used to control movement and block the actuator in both directions, performing the following functions:
Controlled lowering of the load that is not dragged by its weight, since the...
€120.00
(tax excl.)
€145.20
(tax included)
NG-6 pressure limiting valve It serves to prevent a certain pre-set pressure from exceeding
Pressure range 5...315 bar. (SPECIFY PRESSURE)
Flow rate 35 l/min.
Temperature -20ºC / 70ºC
€182.00
(tax excl.)
€220.22
(tax included)
The NG-6 simple overcenter valve is used to control the movement and block the actuator in both directions, performing the following functions: Controlled lowering of the load that is not dragged by its weight, since...
€225.00
(tax excl.)
€272.25
(tax included)
Modular NG-10 flow regulator.
Flow rate 70 l/min.
€168.75
(tax excl.)
€204.19
(tax included)
NG-10 limiting valve
Pressure range 5...315 bar. (SPECIFY PRESSURE)
Flow rate 70 l/min.
Temperature -30 / 80ºC
€370.00
(tax excl.)
€447.70
(tax included)
The overcenter valve is used to control movement and block the actuator in both directions, performing the following functions:
Controlled lowering of the load that is not dragged by its weight, since the valve does...
€52.50
(tax excl.)
€63.53
(tax included)
Modular non-return valve NG-6
Flow rate 35 l/min.
Max pressure 250 bar
Working temperature -20ºC / 70ºC
